With the call for 'Low carbon, innovation, environmental protection' posed in 12th China International Stone Fair, stone industry begains to marching into modernization, and industrial restructruing bursts out.

According to this theme in the fair, contains the direction of future development of stone industry, which is also this 'influence the world power of China's stone industry - Top Ten Influential Enterprises' selection out of the development of enterprises with the notion. with this tendency, China crusher market and related stone industry are required to make differences to meet the society's demands. Fine jaw crusher, VSI impact crusher, hydralic cone crusher all show up. Nowadays, the competition in crusher industry pays more attention to development of energy saving cycle model, innovative products, developing the brand, to enter the capital market ... 'Green industry' becomes the top spot.

For survival in the industry restructuring, we must change the way development of the industry, two of which focus is industrial upgrading, adjusting industrial layout to meet the needs of urban development , to rely on products, technology and management innovation, from the traditional industry to modern stone industry development. New technology and new rule are necessary. Besides development of individual new machine, the whole production line such as stone production line, cement production line, sand making productoin line are also important. We must grasp the quality of stone crushing plant, sand maker, Raymond mill, cement mill and all others. In reality, produced by powder processing, is not only a major source of pollution stone industry, and because of the growing shortage of landfill sites, it has become limited the further development of the entire stone industry problems.

13-12-2011 om 07:17 geschreven door annazhao356  

In stone crushing line, there are jaw crusher, impact crusher, vibrating feeder, vibrating screen, belt conveyor and others. The primary crusher was formerly the custom to consider one set of product gradation, or screen analysis, curves as being suitable to represent the products of both primary (unscreened) and secondary (screened) feeds, making no allowance ore the undersize material which is always present, to some extent, in quarry-run and mine-run materials. The average quarry does not produce as much on this undersize rock as the average mine, but the usual practice in mining operations is to scalp off most of the undersize ahead of the primary crusher. For example, jaw crusher usually is used as primary crusher, primary jaw crusher. We are the professional manufacturer of complete set of crushing plant. Our jaw crusher, impact crusher, cone crusher, hammer crusher, and also belt conveyor are all in excellent quality with low price and enjoy good reputation at home and abroad.

13-12-2011 om 07:16 geschreven door annazhao356  

With the rapid development of science and technology in the 21st century, new industries are booming, the marketing competition become fiercer. The emerging and rapid development of e-business advanced the revolution of traditional industries; it gave a new lease of life and new direction to industries including mining machinery industry.

As the famous machinery brand, Henan Hongxing has its own e-business group. E-business widely changed our work over the past years, many potential buyers can reach our machinery and equipment such as crusher, sand maker, cement production line, ore beneficiation equipment through e-business, it also made commodity circulation quicker and easier. With one click of the mouse, the buyers can send their orders to us, e-business streamlines our business transactions, making them quicker, simpler and more economical. The sustainable development of E-business in China's offered new marketing mode- network marketing for manufacturers. The difference between network marketing and traditional marketing is that networking marketing operates mainly on internet, while traditional marketing run through sales personnel.

Nowadays, e-business platform on the network marketing, such as using alibaba business platform to release the propaganda enterprise products is exerted to establish business connections and trade profits. Based on thie platform, our jaw crusher, impact crusher, ball mill, Raymond mill, flotation machine, dryer and other mamchines have greater business markets.

13-12-2011 om 07:16 geschreven door annazhao356  

Grinder mill Crushed limestone processed can be applied in many fields,and have achieved substantial economic benefits.limestone milling processing industries gradually development in recent years.

Limestone is Mainly a sedimentary rock composed of calcite. Are distributed throughout the country, while the fine texture of the surface and more exposed, vulnerable to exploitation and development of low-cost and easier processing and utilization. Limestone is the largest cement manufacturing applications industry. Cement manufacturing industry has a considerable advantage, since the since the invention of cement, cement products as a main material of construction and has 180-year history. Even in highly developed science and technology of today, do not come up with alternatives, so the investment grinder mill production line for processing of limestone for cement manufacturing is a good way to obtain economic benefits.

In addition the limestone can be used in the manufacture of glass, soda ash, caustic soda, etc., iron with limestone for flux, except gangue, slag making material to do with lime to remove sulfur, phosphorus and other harmful impurities. In life, made of limestone burning process than pure calcium carbonate powder, used as rubber, plastics, paper, toothpaste, cosmetics and other filler. Agriculture, the use of quicklime prepared mixture of lime sulfur, Bordeaux mixture, such as pesticides. Hydrated lime can be applied in soil and soil acidity and improve soil structure, and supply the necessary calcium plants. Tree trunks with stone mortar brush to protect the trees. The use of the chemical industry use of the chemical processing of limestone made of calcium chloride, calcium nitrate, calcium sulfite calcium important, China's Xinjiang abundant reserves of limestone, limestone mining in view of the tremendous economic value, in recent years to develop on the limestone milling processing industry achieved good economic benefits.

Limestone milling machine is the main processing equipment, the application can be expected to adjust the fineness of the new milling machine, suitable for production of limestone powder for various uses. Meet the processing requirements of various industries. Henan HXJQ produce series of mining machinery including Raymond mill, Sand making machine, energy-saving cone ball mill, high pressure micro-powder mill, overpressure trapezium mill, VSI impact crusher, ball mill, primary jaw crusher, etc., the product of a comprehensive process to adapt to the requirements of limestone, a material particle size range from a few dozen head to head 3000, high yield, stable performance. Now many of limestone powder for domestic investors, the success of the production line to install a complete set of milling machine production line, cost-effective for customers to provide the security, milling equipment is the best choice of buyers.

13-12-2011 om 07:15 geschreven door annazhao356  

Henan Hongxing has been titled 'China famous mining machinery brand', which is the professional manufacturer for crushing plant, grinding machine, screening mining machinery, ore benefication equipment, sand making machine. Recent years, the new products Mobile crushing station, VSI impact crusher, Fine jaw crusher and Hydraulic cone crusher have designed and began to sell at home and abroad. Just taking VSI impact crusher as an example to prove the profits the machine creats.

The efficiency of VSI impact crusher, energy required per ton of crushing, overall life of the bearings, and other parts, general breakdown, and time required for it’s maintenance, cost of wear parts, and replacement time, daily lubrication cost and time required for the same should also be considered. The total manufacturing cost of crushing is explained in details.

a. The wastage of energy in friction loss is reduced to a minimum.

b. Life of the bearings in our machine is not less than 10,000 working hours or even more. This is a estimated life.

c. The main shaft of our machine is made from special steel, and no failure or breaking is recorded. The fitment of the shaft is also special, and is not directly connected to the bearings. Shock load if any, due to any reason is soaked by the shaft it self and very less chances for it’s transfer to the bearings.

d. Wear parts are the main thing for the economical running of the machines.

e. A very special design of anvil sectors, particularly for Rotopactor utilizes the residual energy of the particles and makes the edges rounded and gives good surface texture Due to rolling and rubbing action.

13-12-2011 om 07:14 geschreven door annazhao356  

Our cone crusher includes Symons cone crusher, Hydraulic cone crusher, Sprind cone crusher. Spring cone crushers are widely used in industries like metallurgy, construction, road building, chemistry etc, to crush many kinds of mid-hard or hard rocks and ores such as iron ore, limestone, granite, basalt, quartz etc. The standard ones are used for intermediate crushing; the medium ones are used for fine crushing; and the short head ones are used for super thin crushing. Compared with Jaw Crusher, Spring Cone Crusher is of stable structure, high efficiency, easy adjustment, and economical using etc. The spring safety system of crusher acts as an overloading protection system that allows metals to pass through the crushing chamber so as not to damage the Cone Crusher. The safety system uses dry oil and water as two kinds of sealed formation to make plaster powder and engine oil separated to make sure reliable performance. This type of crushing chamber depends upon the size of feeding and fineness of the crushed product. The standard type (PYB) is applied to medium crushing, the medium type is applied to medium or fine crushing and the short head type is applied to fine crushing.

13-12-2011 om 07:13 geschreven door annazhao356  

To make the Ball mill operate good, we must strictly abide by the operation and maintenance procedures.

Before starting the ball mill, check whether the connecting bolt, gears, couplings are tightening. Check whether the oil of the oil tank and the reducer is in the adequacy, and Whether the lubricating device and instrumentation have problems. Determines the flow of pipeline. Check whether there are ore to prevent the Ball Mill Machine running. Check the ring gear and pinion gear case with or without abnormal noise.

The order start machine is:First start the ball mill oil pump. When the oil pressure reach 1.5 ~ 2.0 kg / cm2, it is allowed to start the ball mill, and then start the grading machine. All are functioning properly, then start grinding.

In operation, we must always pay attention to bearing temperature. The temperature shall not exceed 50 ~ 65℃. We also always pay attention to motors, voltage, current, temperature, sound, etc. And pay attention to lubrication system. The temperature of the oil tank shall not exceed 35 ~ 40 ℃, the pressure to the pipeline should be maintained at 1.5 ~ 2.0 kg / cm2. Check the lubrication of transmission components such as gear, main bearing, grading machine reducer. Constantly pay attention to the change of nature of ore, and to take appropriate measures in a timely manner under the circumstances.

When stopping ball mill, first stop the feeder machine, then stop the ball mill machine until the ore has been dealt with. The last is pump. With grading machine screw lifting equipment to raise sand surface, and then stop grading machine.

13-12-2011 om 07:13 geschreven door annazhao356  

The domestic stock market changed frequently influenced by the America stock market, Henan Hongxing Mining Machinery Co. Ltd. reminds investor that it's better to invest on mining machinery than stock.

The stock market is the invisible product in a sense. It was easy to be influenced by people, can’t be seen, can’t be touched and can’t be controlled by the government. The mining machinery industry is the lifeblood of the country, it has great support from the government, also it is the product that you can see and touch.

With the development of the economic and the promotion of economic security room, a climax of building bridge, paving the road is coming. As the builder and executor, the mineral equipment has its own mission. At this stage, the popular mining equipments are crushers and sand-making machineS. The crushers manufactured by HXJQ include Jaw crusher, Impact crusher, Combination crusher, Hammer crusher, Roll crusher, PCZ hammer crusher and so on. Sand-making machines are mainly: Fine jaw crusher, Vertical shaft impact crusher, PE impact crusher. In most situations, the sand-making machinery is used with crusher.

13-12-2011 om 07:12 geschreven door annazhao356  

Mining machinery manufacturing industry is the establishment of an independent state based industrial system, to measure a country's industrial strength is an important symbol.

Broken inside the milling equipment is an important mining machinery components, including jaw crusher, and other broken equipment and Raymond mill, ultrafine powder mill, super mill milling machine dozens of use of diverse equipment, not only in the coal, electricity, chemicals and building materials industries in the deep processing of raw materials play a significant role, but also for railway, highway, water and electricity, the construction of municipal works to provide a high efficient, reliable technical logistical support. Coal, metal and nonmetal mines with the development of more advanced international level of quality, efficient equipment to meet the economic development needs for energy and raw materials of great significance.

Henan Hongxing Mining Machinery Co., Ltd. to be aware of the founding companies to accelerate their product development and innovation, the establishment of systematic and comprehensive after-sales service network and accurately grasp the pulse of the market, organize production according to market demand, allocation of resources, optimize the product structure, develop market, increase revenue to the development of faster and better. Hongxing machines are continually improving the level of technical services, increasing R & D efforts, technology innovation and reform to meet the wave of industry equipment.

Comprehensive production features of today's mining industry point of view, broken machines, milling machines and other mining machinery and equipment are becoming a large, digital intelligence and ecological energy conservation. Henan Hongxing Mining Machinery Co., Ltd. As the first crusher, grinding machine equipment manufacturer, has been continuously forge ahead, always standing trade front. Hongxing machines are taking every step, there were not closely meet the domestic mining, chemical industry, road construction industry's actual production and demand, market demand for the most fundamental basis for strong technical support for R & D strength, star machine as one by one excellent large-scale construction projects equipment suppliers. The coming year will be the rapid growth of the world's mining machinery industry, the year, especially in China's mining equipment manufacturers, the rare opportunities for development.

13-12-2011 om 07:09 geschreven door annazhao356  

a. When cone crusher is operating, even feeding should be delivered. If the feeding is uneven, production capacity will be reduced, product granularity is too big, spring action is frequent, pressure of bowl-shaped bearing is high, energy consumption is increasing.

b. Iron removing device must be installed to prevent from iron overload. If iron overload is frequent, it will probably cause axis failure accident.

c. Full capacity must be realized, otherwise, product granularity is over rough.

d. Distribution of crushing ratio of production line must be reasonable, so as to give full play to maximum crushing efficiency

e. Spring pressure can not be too tight, over pressure will cause off-axis accident occurred. If pressure is over low, spring will bounce frequently, which will affect the normal operation of crusher, and product granularity is becoming rough.

f. Lubricating oil temperature cannot be too high or too low, otherwise, it will affect normal operation of the machine.

g. Lubricating oil must be often changed, which can not be too dirty, otherwise, it will cause increasing of abrasion for gear, bowl-shaped tile, sleeve, even failure.

h. Conveyor belt must not be installed too tight, otherwise, it will cause shaft is not flexible or broken; must not be too loose, or it will cause crusher stop working.

i. Feeding material can not be too sticky or too wet, fine particle can not be too much or too big, otherwise, it will cause crusher stop working.

j. Material stacking in discharge gate of cone crush will also cause crusher stop working.

12-12-2011 om 07:27 geschreven door annazhao356  

Doing any thing, choosing one article, which obey the line - Suit the remedy to the case. Sand making equipment is used for sand making production line.

Components of the sand-making production line:

The line contains jaw crusher, impact crusher(sand maker), vibrating screen (circular vibrating screen), sand washer, belt conveyor. Depending on different technology requirements, designing the suitable model can play the best performance.

Brief introduction of the sand-making production line:

The raw materials are first put into elementary-crushing machine for crush, then the belt conveyor transfers the elementary products to the secondary-crushing machine for secondary crush. The secondary products will be separated into two kinds by the vibrating screen. The parts satisfying the standard of the Vertical Shaft Impact Crusher will be conveyed to the sand-making machine and the other parts will return to the secondary-crushing machine. The parts into the sand-making machine will be the finished products after being washed in the sand-washing machine. The other parts will be for the secondary crush.

HXJQ design and produce a full set of sand production line equipment used for hard limestone, granite, basalt, river gravel, slag and other materials. For high efficiency and best profits, we provide the most professional design of sand making plant. Until now, our machines have been sold and exported at home and abroad. Not only in the quality of sand, but also in the energy saving, HXJQ have been at an international leading level.

12-12-2011 om 07:27 geschreven door annazhao356  

For all businessmen and any enterprise, it's the commom wish to make great benefits with low costs. We are the professioanl manufacturer of stone crushing line, jaw crusher, impact crusher, cone crusher, hammer crusher etc. How to set a high quality stone crushing line with low costs to achieve the goal.

Stone production line generally consist of feeding equipment, crushing equipment( Crusher equipment for sale ), transportation equipment, screening equipment, how to choose the crusher type to achieve Low investment, high productivity, and the stone out size , grain shape Meet the requirements of the quarry, which kind of crusher we should use ,can reach all this requirements?

Generally speaking, sand production line consists of feeding equipment, crushing equipment, screening equipment and transport equipment, and they are general-purpose equipment, no too much difference in basically, but still have to take the characteristics of the material into account, when select the machine, should pay attention to the element of water capacity, hardness, material size, especially the request of capacity per hour. A variety of styles crusher because of its own different characteristics, their expertise also different, such as jaw crusher is suite for crushing some hard stone, opposite, not only over skill, but also the final product beyond the standard. The common crushing machines to be used in stone crushing line are jaw crusher, impact crusher and cone crusher.

Currently, the main screening machines wildly used in stone crushing line are Circular and linear vibrating screen, of which, circular vibrating screen is most common vibrating machine. The vibrating screen is mainly used for powder and granular materials selection and classification, Widely used in plastics, abrasives, chemicals, pharmaceuticals, building materials, food, carbon, fertilizer, refractory materials, light industry, mining, coal, metallurgical and other industries.

Stone production line is generally used conveyor belt as conveying equipment, which has the advantage of big transmission capacity, long transmission distance, smooth transportation, no relative motion between material and conveyor, low noise, simple structure, easy maintenance, energy consumption, parts standardization, etc., in the quarry, It is widely used in stones factory and other places.

We must first sharpen his tools, before we want to do work well, such as the selection of the crushing machine in stone crushing line( Stone crushing plant price ), Choose energy-efficient, high durability of crushing equipment, it is not only save the cost for Quarry Company, but also reduce the environmental pollution, raise the earnings, realize the double win of economic and social benefits.

12-12-2011 om 07:26 geschreven door annazhao356  

I graduated in Year 2009, and have changed many jobs. This year, I become one cleark of Henan Hongxing Mining Machinery Co. Ltd. which is the professional manufacturer of complete sets of mining machinery: ball mill, jaw crusher, impact crusher, rod mill, energy-saving cone ball mill, sand maker, ore beneficiation equipment, Raymond mill and various mining machines. In Hongxing, I meet a kind girl - Little Summer, who is my best collegue and friend here. She came here 2 days earlier than me, and she is younger than me, but we have many similarities.

Recent years, Hongxing develops very greatly, and also the business is larger and larger. With the China crusher markets increasing, our jaw crushers, impact crusher, cone crusher and other types of stone crushing equipment. With the raising business, the bosses announce better treatment together with more serious rules. This is reality; this is life. For bright future, work on with my Summer! As to He, I will put him into my heart.

12-12-2011 om 07:25 geschreven door annazhao356  

Recently, sand and gravel industry has become a hot topic on the market, which make Sand and gravel production line has become the object of discussion. According to source, sand and gravel lines has many types, its easy to mix them up, making wrong judgments. In response to this situation, here we make a discussion on this situation to talk about the difference of sand making plant (impact crusher, VSI sand maker) and sand production line equipment.

Sand production line consist of feeder, jaw crusher, fine jaw crusher, 'stone to stone' shaft impact crusher, vibrating screen, sand washing machines, belt conveyors, centralized electronic control and other equipment, to meet customer demand, can be matched cone crusher, dust removal equipment. Then The stone production line consist of jaw crusher (rough broken), impact crusher (fine broken), shaft impact crusher, vibrating feeder, vibrating screen, sand washing machine, belt conveyor and other equipment.

Sand production line can be used to crush hard limestone, granite, basalt, river pebbles, pebbles, slag and other materials, artificial sand and aggregate operations for water and electricity, construction, building materials, highways, urban construction and other industry applications. The equipments used in stone production line (sand and gravel production line) are to produce sand and stone used in construction.

Sand production line material (limestone, granite, basalt, gneiss, river pebbles, pebbles, etc.) complete the primary crushing through the feeder in to jaw crusher, then the final stone complete the second crushing through the transportation of belt conveyor in to fine jaw crusher, After secondary crushing, stone transported by conveyor belt into the 'stone to stone' impact crusher broken again, the broken stone material Transported by belt conveyor to vibrating screen, then stone was screening into different sizes, a part of stone which is meet the Customers size requirements transported to Product stockpile by conveyor belt, then the Substandard stones was get back to shaft impact crusher (impact crusher for sale) to be crushing again, form a closed loop.

12-12-2011 om 07:24 geschreven door annazhao356  

With the approaching of information technology era, China mining machinery industry shows great changes not only in industry structure, but also industry culture. Jaw crusher is the main machine in mining industry for stone crushing. Stone jaw crusher can be used in road construction, metallurgy, chemicals, kaolin, concrete and so on. Take the concrete crushing plant as example. Generally there are concrete crushing stage, concrete grinding process, and concrete products screening process in the whole concrete crushing plant. About the concrete crushing equipment, jaw crusher works as typical primary crusher.

From the primary crushing to the secondary crushing, concrete is crushed into smaller pieces eventually. Also, there are vibrating screening equipment which can separate different sizes products. For detail introduction, you can come to our website to learn all our products: jaw crusher, impact crusher, cone crusher, hammer crusher, cement production line.

Apart from concrete crushing, jaw crusher is widely applied to crush high hardness ,mid hardness and soft rocks and ores such as slag, construction materials, marble ,etc, whose pressure resistance strength is under 200Mpa.

As we know, jaw crusher is widely used in mining and construction. Actually the stone crusher is also widely applied in metallurgical industry, road and railway building, smelting, hydraulic and chemical industries, etc.

12-12-2011 om 07:23 geschreven door annazhao356  

Raymond mill is mainly applied to the powder processing of mineral products in industries of metallurgy, construction, chemistry, and mining etc. Raymond mill can produce powder from more than 280 kinds of non-flammable and non-explosive mineral materials with Mohs hardness below 7 and humidity below 6%, such as barite, limestone, quartz, calcite, granite, porcelain clay, basalt, gypsum etc. The final size is between 613micron and 440 micron(0.613mm—0.044mm).

How to repair and maintain Raymond mill well and exactly?

1). During the application of our raymond mill, some personnel shall be arranged to take responsibility of management from beginning to end. The operators must be qualified with the required technical knowledge of opreating grinding mills. Before the installation of this grinding mill, the persons related to the operation should receive technical training and fully understand the operating principle, performance and regulations of the raymond mill.

2). In order to guarantee the raymond mill in a normal working state, a Safety Operation System for the Maintenance of the equipment must be established. Only in this way can the raymond mill be guaranteed to have a long-term and safe operation. Meanwhile, it is necessary to have the required repairing tools, lubricant and grease, spare parts and accessories during the operation.

3). After some period of running, the raymond mill should receive an examination and repairing. The components vulnerable to worn out, such as grinding roller, grinding ring, relieving tool etc. should be repaired or replaced. Before and after the operation, a careful examination should be carried out for the connecting screws, bolts and nuts on the grinding rollers so as to find whether they are loose or sufficiently lubricated.

4). When their application time surpassing about 500 hours, all the rolling bearings in the roller sleeves of raymond mill must be cleaned, and the damaged parts should be replaced. The oiling tool can be either a manual oiling pump or grease gun.

12-12-2011 om 07:22 geschreven door annazhao356  

As we know, we have entered into the information technology era not only for information industry, construction industry and also mechanical industry. Accompanied with the benefits of information technology, there is the economic impact. jaw crusher, sand maker

The economic impact of information technology has been a subject of a great deal of debate. For business economists, it is useful to identify how information technology (IT) is likely to impact the economy, because IT (defined as computer and communications technology and its applications) is likely to have a substantial impact on the economy's growth during the coming decades. The reason for this is the use of IT by nearly all industries in the economy's base, so that IT becomes a universal input to nearly all other outputs. If IT costs decline, they can create substantial economic gains for many of the industries that use IT, because money spent on IT can be invested in other inputs and improvements in production or services. Furthermore, because business relies upon IT to do a wide range of tasks and to create competitive advantage, by facilitating these tasks for end users, important gains are achieved that are difficult to measure in a classic input-output framework. In addition, IT, seen in a larger context, should have even wider impacts on the economy, because new channels of communications, such as the Internet, cellular television, and broadband applications, will provide business with new channels to reach customers and suppliers. flotation machine, impact crusher

12-12-2011 om 07:22 geschreven door annazhao356  

As one of the most important operations in aggregate process, crushing is a process of suiting customer’s requirements by breaking and shaping mine rock or other stones to reduce their size for further processing. Generally, there are more or less three phases: primary crushing, secondary crushing and tertiary crushing. The primary crusher(usually jaw crusher, sometimes impact crusher, it depends on your material type, size, hardness, etc.) reduces materials from under 1.5m to under 0.3m; For further size reducement, secoondary crushing can help you reach below 40 or 50mm, and in this step, cone crusher is usually employed in consideration of product size and shape. When it comes to tertiary crushing, material size is generally reduced to below 20mm.

As to the crushing methods, there are two most common types: compression crushers and impact crushers. Compression crushers adopt the theory of squeezing or pressing between rigid surfaces, such as jaw crusher, cone crusher, dual-roller crusher, etc., while impact crushers employ impact, such as impact crusher, vertical shaft impact crusher, super-fineness energy-saving crusher, etc. This type of crusher usually has metal bars, to be specific, blow bar or hammers, beaters, impellors, and they are attached to fixed rotors on a rotating shaft surrounded by crushing chamber with metal impact plates or bars.

12-12-2011 om 07:12 geschreven door annazhao356  

With a small raymond cement mill floor area and good entirety, raymond cement mill can operate independently and automatically from piece crushing to raymond cement mill product packaging.Powder ground by High Efficiency raymond cement mill can be screened at a rate of above 99%, raymond cement mill other grinders are unable to achieve. raymond cement mill Electromagnetic-vibrating feeder is easily regulated, small in volume and light in weight. raymond cement mill saves oil and electricity, and enjoys convenient maintenance. The raymond cement mill adoption of it shall ensure the uniformity of feeding.raymond cement mill Electricity is central controlled without manual operation in host machine room.raymond cement mill Host machine driving unit adopts closed reduction box,raymond cement mill achieves stable raymond cement mill transmission and reliable rotation without leakage of oil.raymond cement mill Shovel tool rest for host machine keeps in touch with raymond cement mill materiel while rotating. raymond cement mill is composed of two parts, of raymond cement mill bracket may be changed after abrasion through dismounting bolts connected.

12-12-2011 om 07:11 geschreven door annazhao356  

The serial numbers on this bunch of new high-quality bogus RMB 100 banknotes are LN37638309, LN37638313 and LN37638302. Police seized 30,000 yuan worth of high-quality counterfeit 100 yuan notes in Guigang city, Guangxi Zhuang autonomous region, South China. It's difficult to tell these fake notes from real ones as they carry water marks, metal wires and a number of other anti-counterfeit features. [Xinhua]

10-12-2011 om 06:30 geschreven door annazhao356